Linux Kernel /etc/sysctl.conf Security Hardening

How do I set advanced security options of the TCP/IP stack and virtual memory to improve security and performance of my system? How do I configure Linux kernel to prevent certain kinds of attacks using /etc/sysctl.conf? How do I set Linux kernel parameters?

sysctl is an interface that allows you to make changes to a running Linux kernel. With /etc/sysctl.conf you can configure various Linux networking and system settings such as:

 

 

 

  1. Limit network-transmitted configuration for IPv4
  2. Limit network-transmitted configuration for IPv6
  3. Turn on execshield protection
  4. Prevent against the common ‘syn flood attack’
  5. Turn on source IP address verification
  6. Prevents a cracker from using a spoofing attack against the IP address of the server.
  7. Logs several types of suspicious packets, such as spoofed packets, source-routed packets, and redirects.

sysctl command

The sysctl command is used to modify kernel parameters at runtime. /etc/sysctl.conf is a text file containing sysctl values to be read in and set by sysct at boot time. To view current values, enter:
# sysctl -a
# sysctl -A
# sysctl mib
# sysctl net.ipv4.conf.all.rp_filter

To load settings, enter:
# sysctl -p

Sample /etc/sysctl.conf

Edit /etc/sysctl.conf and update it as follows. The file is documented with comments. However, I recommend reading the official Linux kernel sysctl tuning help file (see below):

# The following is suitable for dedicated web server, mail, ftp server etc. 
# ---------------------------------------
# BOOLEAN Values:
# a) 0 (zero) - disabled / no / false
# b) Non zero - enabled / yes / true
# --------------------------------------
# Controls IP packet forwarding
net.ipv4.ip_forward = 0
 
# Controls source route verification
net.ipv4.conf.default.rp_filter = 1
 
# Do not accept source routing
net.ipv4.conf.default.accept_source_route = 0
 
# Controls the System Request debugging functionality of the kernel
kernel.sysrq = 0
 
# Controls whether core dumps will append the PID to the core filename
# Useful for debugging multi-threaded applications
kernel.core_uses_pid = 1
 
# Controls the use of TCP syncookies
#net.ipv4.tcp_syncookies = 1
net.ipv4.tcp_synack_retries = 2
 
########## IPv4 networking start ##############
# Send redirects, if router, but this is just server
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.default.send_redirects = 0
 
# Accept packets with SRR option? No
net.ipv4.conf.all.accept_source_route = 0
 
# Accept Redirects? No, this is not router
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.all.secure_redirects = 0
 
# Log packets with impossible addresses to kernel log? yes
net.ipv4.conf.all.log_martians = 1
net.ipv4.conf.default.accept_source_route = 0
net.ipv4.conf.default.accept_redirects = 0
net.ipv4.conf.default.secure_redirects = 0
 
# Ignore all ICMP ECHO and TIMESTAMP requests sent to it via broadcast/multicast
net.ipv4.icmp_echo_ignore_broadcasts = 1
 
# Prevent against the common 'syn flood attack'
net.ipv4.tcp_syncookies = 1
 
# Enable source validation by reversed path, as specified in RFC1812
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.default.rp_filter = 1
 
########## IPv6 networking start ##############
# Number of Router Solicitations to send until assuming no routers are present.
# This is host and not router
net.ipv6.conf.default.router_solicitations = 0
 
# Accept Router Preference in RA?
net.ipv6.conf.default.accept_ra_rtr_pref = 0
 
# Learn Prefix Information in Router Advertisement
net.ipv6.conf.default.accept_ra_pinfo = 0
 
# Setting controls whether the system will accept Hop Limit settings from a router advertisement
net.ipv6.conf.default.accept_ra_defrtr = 0
 
#router advertisements can cause the system to assign a global unicast address to an interface
net.ipv6.conf.default.autoconf = 0
 
#how many neighbor solicitations to send out per address?
net.ipv6.conf.default.dad_transmits = 0
 
# How many global unicast IPv6 addresses can be assigned to each interface?
net.ipv6.conf.default.max_addresses = 1
 
########## IPv6 networking ends ##############
 
#Enable ExecShield protection
kernel.exec-shield = 1
kernel.randomize_va_space = 1
 
# TCP and memory optimization 
# increase TCP max buffer size setable using setsockopt()
#net.ipv4.tcp_rmem = 4096 87380 8388608
#net.ipv4.tcp_wmem = 4096 87380 8388608
 
# increase Linux auto tuning TCP buffer limits
#net.core.rmem_max = 8388608
#net.core.wmem_max = 8388608
#net.core.netdev_max_backlog = 5000
#net.ipv4.tcp_window_scaling = 1
 
# increase system file descriptor limit    
fs.file-max = 65535
 
#Allow for more PIDs 
kernel.pid_max = 65536
 
#Increase system IP port limits
net.ipv4.ip_local_port_range = 2000 65000

 

0 (0)
Article Rating (No Votes)
Rate this article
Attachments
There are no attachments for this article.
Comments
There are no comments for this article. Be the first to post a comment.
Full Name
Email Address
Security Code Security Code
Related Articles RSS Feed
How To Use Systemctl to Manage Systemd Services and Units
Viewed 8661 times since Mon, Dec 7, 2020
SPRAWDZONA KONFIGURACJA RSYSLOG I LOGROTATE, JAKO ZEWNĘTRZNEGO SERWERA SYSLOG
Viewed 4922 times since Fri, Nov 30, 2018
How to remove CTRL-M (^M) characters from a file in Linux
Viewed 3872 times since Thu, Feb 7, 2019
Open SSL Encrypt & Decrypt Files With Password Using OpenSSL
Viewed 11045 times since Mon, Feb 18, 2019
Enabling or disabling a repository using Red Hat Subscription Management
Viewed 14926 times since Mon, Oct 29, 2018
RHCS6: Show/Add GFS2/GFS journals
Viewed 13590 times since Sun, Jun 3, 2018
RHEL: Crash kernel dumps configuration and analysis on RHEL 7
Viewed 8774 times since Sat, Jun 2, 2018
RHEL: Getting/Setting hardware clock’s time
Viewed 4788 times since Sat, Jun 2, 2018
List of 10 Must Know Oracle Database Parameters for Database Administrator
Viewed 147642 times since Thu, Jun 21, 2018
ZFS: Remove an existing zfs filesystem
Viewed 2998 times since Sun, Jun 3, 2018