Create a Linux Swap File

Create a Linux Swap File

  • Last updated on: 2015-08-19
  •  
  • Authored by: Trey Hoehne

Swap is space on a disk that is reserved to be used as virtual memory. When a Linux server runs out of memory, the kernel can move inactive processes into swap to make room for active processes in the working memory.

A swap partition is not present on Cloud Servers by default, but swap can be added to a server by allocating a swap file. The performance of a swap file is similar to that of a swap partition while making it easier to control the swap size without repartitioning a volume. How aggressively the server will use this swap space can be controlled by modifying the system’s swappiness value.

The steps below discuss the creation of a swap file on Linux and modifying the system swappiness value.

How do I add swap?

To add 1GB of swap to your server, for example, follow these steps:

  1. Create the file to be used for swap.

    sudo fallocate -l 1G /mnt/1GB.swap
    

    If fallocate fails or is not installed, run the following command.

    sudo dd if=/dev/zero of=/mnt/1GB.swap bs=1024 count=1048576
    
  2. Format the file for swap.

    sudo mkswap /mnt/1GB.swap
    
  3. Add the file to the system as a swap file.

    sudo swapon /mnt/1GB.swap
    
  4. Add this line to the end of /etc/fstab to make the change permanent.

    /mnt/1GB.swap  none  swap  sw 0  0
    
  5. To change the swappiness value edit /etc/sysctl.conf and add the following line.

    vm.swappiness=10
    

    Start with a value of 10 and increase if needed. A typical default value for swappiness is 60. The higher the number (up to 100), the more often swap is utilized.

    How much swappiness affects performance depends on how your memory is being used, so experiment to find an optimal value. At 0 the swap file will only be used when the system runs completely out of memory. Higher values let the system swap idle processes out to allow the system to free memory for disk caching, potentially improving overall system performance.

  6. Check that the swap file was created.

    sudo swapon -s
    
  7. Reboot the server to ensure that the changes go into effect.

Note: By following these instructions on a newly created Rackspace server, the resulting swap file is world-readable. To prevent the file from being world-readable, you should set up the correct permissions on the swap partition/file by running the following command to change the permission:

chmod 600 /mnt/1GB.swap

In most cases, the only user that needs access to the swap partition is the root user.

0 (0)
Article Rating (No Votes)
Rate this article
Attachments
There are no attachments for this article.
Comments
There are no comments for this article. Be the first to post a comment.
Full Name
Email Address
Security Code Security Code
Related Articles RSS Feed
How to configure an SSH proxy server with Squid
Viewed 3378 times since Sun, Dec 6, 2020
CentOS / RHEL : How to move a Volume Group from one system to another
Viewed 3887 times since Mon, Jan 28, 2019
RHCS6: Quorum disk and heuristics
Viewed 4597 times since Sun, Jun 3, 2018
Linux - How to get IP and MAC address of ethernet adapter in Linux
Viewed 2917 times since Fri, Jun 8, 2018
List usernames instead of uids with the ps command for long usernames
Viewed 2608 times since Wed, Jul 25, 2018
Używanie rsync poprzez Secure Shell
Viewed 41497 times since Thu, May 24, 2018
systemd Auto-restart a crashed service in systemd
Viewed 3522 times since Fri, Jan 17, 2020
How to mount software RAID1 member using mdadm
Viewed 3246 times since Wed, Oct 3, 2018
high swap space utilization in LINUX
Viewed 6761 times since Fri, Jul 13, 2018
Using stunnel and TinyProxy to obfuscate HTTP traffic
Viewed 7226 times since Fri, Sep 28, 2018