How to Register and Enable Red Hat Subscription, Repositories and Updates for RHEL 7.0 Server
After the last tutorial on minimal installation of Red Hat Enterprise 7.0, it’s time to register your system to Red Hat Subscription Service and enable your system repositories and perform a full system update.
Enable Red Hat Subscription, Reposiories and Updates
A subscription service has the role to identify registered systems with the products installed on them. Local Subscription Manager service tracks down the installed software products, available and used subscriptions and communicates with the Red Hat Customer Portal through tools like YUM.
Requirements
This tutorial guides you on how we can perform tasks like registering new RHEL 7.0, how to active subscription and repositories before actually be able to update our system.
Step 1: Register and Active Red Hat Subscription
1. To register your system to Customer Portal Subscription Management use the following command followed by the credentials used to login to Red Hat Customer Portal.
Register RHEL 7 Subscription
NOTE: After the system is successfully authenticated an ID will be displayed on your prompt for your system.
2. To unregister your system use unregister switch, which will remove the system’s entry from the subscription service and all subscriptions, and will deletes its identity and subscription certificates on local machine.
3. To get a list of all your available subscriptions use list switch and note down your Subscription Pool ID that you want to active it on your system.
List Red Hat Subscriptions
4. To active it a subscription use the Subscription Pool ID, but be aware that when purchase one, it is valid for a specified period of time, so make sure you buy a new period of time before expiring. Because this system is for tests, I only use the 30 Day Self-Supported RHEL free subscription. To activate a subscription use the following command.
Red Hat Subscription Pool ID
5. To get a status of your consumed subscriptions use the following command.
Verify Red Hat Subscription Status
6. To check your enabled subscriptions use the below command.
Check Enabled Red Hat Subscription Lists
7. If you want to remove all your active subscriptions use –all argument or just provide a subscription serial if you want to remove a specific pool only.
Remove Red Hat Subscriptions
8. To list the available service levels on your RHEL 7.0 system use the following command and if you want to set a your desired level use the switch –set on service-level command.
List RHEL Available Service Levels
Step 2: Enable Yum Repositories
9. After you system has been registered to Red Hat Customer Portal and a Subscription has been activated in your system you can start listing and enabling system Repositories. To get a list of all your provided repositories through a certain subscription use the next command.
Enable Yum Repositories on RHEL
NOTE: A long repositories list should appear and you can status to see if certain repositories are enabled (the ones with 1 on Enabled).
10. A more simple output the command yum repolist all should generate through, and you can, also, verify if certain repos are enabled.
List All RHEL Repositories
Verify Enabled Repositories on RHEL
11. To view only the enabled system repositories use the following command.
View System Enabled Repositories
12. Now if you want to enable a certain repo on you system, open /etc/yum.repos.d/redhat.repo file and make sure you change the line enabled from 0 to 1 on every specific repo you want to activate.
Enable Certian Repositories on RHEL
NOTE: Here I’ve enabled RHEL 7 Server Optional RPMs repositories which I will need later to install some important PHP moduleson a LAMP server.
13. After you edited the file and enabled all your needed Repositories using the procedure above, run yum repolist all or just yum repolist, again to verify repos status like in the screenshots below.
Verify All Repo Status
List All Enabled Repositories
Step 3: Full Update RHEL 7.0
14. After everything concerning subscriptions and repositories has been set, upgrade your system to make sure your system has the latest packages, kernels and security patches up to date, issuing the following command.
Update RHEL 7
That’s all! Now your system is up to date and you can start perform other important task like starting to build a complete web environment for productions by installing all the necessary software packages, which will be covered in future tutorials.
Subscribe to Article
Print Article
Email Article to Friend
Export to PDF
Export to MS Word