RHEL: What is "SysRq key" and how to use it

RHEL: What is "SysRq key" and how to use it

# Tested on RHEL 5, 6 & 7

# What is the "Magic" 'SysRq' key?
# ------------------------------------------------------------------------------------------

# According to the Linux kernel documentation:
#  It is a 'magical' key combo you can hit which the kernel will respond to regardless of
#  whatever else it is doing, even if the console is unresponsive.
# The 'SysRq' key is one of the best (and sometimes the only) way to determine what a
# machine is really doing. It is useful when a system appears to be "hung" or for
# diagnosing elusive, transient, kernel-related problems.

# How do I enable and disable the 'SysRq' key?
# ------------------------------------------------------------------------------------------

# For security reasons, Red Hat Enterprise Linux disables the 'SysRq' key by default. To
# enable it, run:

echo 1 > /proc/sys/kernel/sysrq

# Or: sysctl -w kernel.sysrq=1

# List of possible values in /proc/sys/kernel/sysrq:
#  0 - disable sysrq completely
#  1 - enable all functions of sysrq
#    >1 - bitmask of allowed sysrq functions (see below for detailed function description):
#      2 - enable control of console logging level
#      4 - enable control of keyboard (SAK, unraw)
#      8 - enable debugging dumps of processes etc.
#     16 - enable sync command
#     32 - enable remount read-only
#     64 - enable signalling of processes (term, kill, oom-kill)
#    128 - allow reboot/poweroff
#    256 - allow nicing of all RT tasks

# To disable it:

echo 0 > /proc/sys/kernel/sysrq

# Or: sysctl -w kernel.sysrq=0

# To enable it permanently, set the kernel.sysrq value to 1. That will cause it to be
# enabled on start up

# RHEL 5 & 6
vi /etc/sysctl.conf
   kernel.sysrq = 1

# RHEL 7
vi /usr/lib/sysctl.d/50-default.conf
   kernel.sysrq = 1

# Since enabling 'SysRq' gives you physical console access extra abilities, it is recommended
# to disable it when not troubleshooting a problem or to ensure that physical console
# access is properly secured.

# How do I trigger a 'SysRq' event?
# ------------------------------------------------------------------------------------------

# There are several ways to trigger a 'SysRq' event. On a normal system, with an AT
# keyboard, events can be triggered from the console with the following key combination:

# Alt+PrintScreen+[CommandKey]

# For instance, to tell the kernel to dump memory info (command key "m"), you would hold
# down the "Alt" and "Print Screen keys", and then hit the m key.

# Note that this will not work from an X Window System screen. You should first change to
# a text virtual terminal. Hit Ctrl+Alt+F1 to switch to the first virtual console prior to
# hitting the 'SysRq' key combination.

# On a serial console, you can achieve the same effect by sending a Break signal to the
# console and then hitting the command key within 5 seconds. This also works for virtual
# serial console access through an out-of-band service processor or remote console like
# HP iLO, Sun ILOM and IBM RSA.
# Refer to service processor specific documentation for details on how to send a Break
# signal; for example, How to trigger SysRq over an HP iLo Virtual Serial Port (VSP).

# If you have a root shell on the machine (and the system is responding enough for you to
# do so), you can also write the command key character to the /proc/sysrq-trigger file.
# This is useful for triggering this info when you are not on the system console or for
# triggering it from scripts.

echo 'm' > /proc/sysrq-trigger

# When I trigger a 'SysRq' event that generates output, where does it go?
# ------------------------------------------------------------------------------------------

# When a 'SysRq' command is triggered, the kernel will print out the information to the
# kernel ring buffer and to the system console. This information is normally logged via
# syslog to /var/log/messages.

# Unfortunately, when dealing with machines that are extremely unresponsive, syslogd is
# often unable to log these events. In these situations, provisioning a serial console is
# often recommended for collecting the data.

# What sort of 'SysRq' events can be triggered?
# ------------------------------------------------------------------------------------------

# There are several 'SysRq' events that can be triggered once the 'SysRq' facility is
# enabled. These vary somewhat between kernel versions, but there are a few that are
# commonly used:

#  m - dump information about memory allocation
#  t - dump thread state information
#  p - dump current CPU registers and flags
#  c - intentionally crash the system (useful for forcing a disk or netdump)
#  s - immediately sync all mounted filesystems
#  u - immediately remount all filesystems read-only
#  b - immediately reboot the machine
#  o - immediately power off the machine (if configured and supported)
#  f - start the Out Of Memory Killer (OOM)
#  w - dumps tasks that are in uninterruptible (blocked) state
0 (0)
Article Rating (No Votes)
Rate this article
There are no attachments for this article.
There are no comments for this article. Be the first to post a comment.
Full Name
Email Address
Security Code Security Code
Related Articles RSS Feed
Installing and Configuring stunnel on CentOS 6
Viewed 873 times since Fri, Sep 28, 2018
RHEL: iSCSI target/initiator configuration on RHEL7
Viewed 1270 times since Sat, Jun 2, 2018
RHEL: Adding a boot entry to GRUB/GRUB2 configuration
Viewed 1026 times since Sun, May 27, 2018
RHEL: Multipathing basics
Viewed 1129 times since Sat, Jun 2, 2018
systemd Auto-restart a crashed service in systemd
Viewed 307 times since Fri, Jan 17, 2020
Linux - How to unlock and reset user’s account
Viewed 500 times since Fri, Jun 8, 2018
How to recover error - Audit error: dispatch err (pipe full) event lost
Viewed 3706 times since Tue, Aug 6, 2019
stunnel bacula
Viewed 438 times since Fri, Sep 28, 2018
How to do a Filesystem Resize (ext3/ext4) on Redhat running on VMware
Viewed 1181 times since Wed, Jul 25, 2018
LVM: Reduce an existing Logical Volume / Filesystem
Viewed 618 times since Sat, Jun 2, 2018